| 192.25.2500.990.41.1502 Standard 5 Slewing Ring Bearings | Width Plain B:9.5 mm; Shielded or Sealed B1:12.7 mm; Sealed Speed Rating n3:9000 rpm; d:25.400 mm; Accessories:Without Accessories; Oil Speed Rating Open/Shielded n2:16000 rpm; Fillet Radius ra:0.79 mm; Basic Dynamic Radial Load Rating C:10100 N; Basic Static Radial Load Rating Co:6000 N; D:50.8000 mm; Grease Speed Rating Open/Shielded n1:13000 rpm; |
| 281.30.1400.013 Type 110/1600.1 Standard 5 Slewing Ring Bearings | Sealed Speed Rating n3:3600 rpm; d:65.000 mm; D:120.0000 mm; B:38.10 mm; Fillet Radius ra:1.50 mm; Oil Speed Rating n2:4800 rpm; Basic Dynamic Radial Load Rating C:88000 N; Grease Speed Rating n1:3600 rpm; Basic Static Radial Load Rating Co:106000 N; Accessories:Two Seals & Snap-Rin; |
| 11.40.2795.000.11.1502 Standard 5 Slewing Ring Bearings | Preload class C GC:240 N; Calculation factor f2C:1.05; Preload class B GB:120 N; Calculation factor fHC:1.02; Static axial stiffness, preload class C:76 N/µm; Mass bearing:0.17 kg; Calculation factor f2A:1; Calculation factor f:1.06; Preload class A GA:60 N; B:15 mm; Basic static load rating C0:11 kN; d:40 mm; D:68 mm; D1:58.8 mm; Static axial stiffness, preload class A:42 N/µm; d2:49.2 mm; |
| 11.35.2620.000.11.1503 Standard 5 Slewing Ring Bearings | Mass bushing:0.04 kg; Tolerance shaft:e7; B1:4 mm; B:16 mm; D1:32 mm; D:25 mm; h:18 mm; α:105 °; a:3 mm; d:17 mm; Coefficient of friction µ min.:0.08; Coefficient of friction µ max.:0.15; Specific static load factor K0:45 N/mm²; Permissible sliding velocity v min.:0 m/s; Specific dynamic load factor K:25 N/mm²; Tolerance housing:H7; Permissible sliding velocity v max.:0.5 m/s; |
| 61.25.1250.101.21.1504 Standard 5 Slewing Ring Bearings | Fillet Radius ra:1.00 mm; Sealed Speed Rating n3:3600 rpm; Grease Speed Rating Open/Shielded n1:6000 rpm; D:110.0000 mm; Basic Static Radial Load Rating Co:32500 N; d:70.000 mm; Oil Speed Rating Open/Shielded n2:7000 rpm; Basic Dynamic Radial Load Rating C:41000 N; Accessories:One Seal; B:20.00 mm; |
| 280.30.1375.013 Type 110/1500. Standard 5 Slewing Ring Bearings | Basic Static Radial Load Rating Co:65500 N; Accessories:Two Shields & Snap-R; Grease Speed Rating Open/Shielded n1:4300 rpm; d:65.000 mm; Oil Speed Rating Open/Shielded n2:5300 rpm; Basic Dynamic Radial Load Rating C:69300 N; B:23.00 mm; Fillet Radius ra:1.50 mm; D:120.0000 mm; |
| 12.20.1360.001.21.1504 Standard 5 Slewing Ring Bearings | r, r1,2 min.:0.3 mm; F:14 mm; B:20 mm; Mass inner ring:0.011 kg; d:10 mm; |
| 161.40.2128.891.41.1503 Standard 5 Slewing Ring Bearings | Hydraulic nut:HMV 30 E; B1:111 mm; Mass adapter sleeve assembly:5.8 kg; d1:131.762 mm; B:30 mm; d3:195 mm; G:M 150x2; d:150 mm; |
| 62.50.2490.001.49.1504 Standard 5 Slewing Ring Bearings | r1 min.:0.3 mm; Material constant KM:330; N1 max.:18 mm; C1 max.:14 mm; G:M 14x1.5; Specific dynamic load factor K:100 N/mm²; d2 max.:41 mm; Basic dynamic load rating C:17.6 kN; Size bolt with internal hexagon:M 6; Tightening torque bolt with internal hexagon:9.5 N·m; l7 min.:17 mm; h1:44 mm; d:16 mm; dk:23 mm; l4 max.:65 mm; B:16 mm; Basic static load rating C0:32.5 kN; l3 min.:19 mm; |
| 91.35.1802.991.41.1502 Standard 5 Slewing Ring Bearings | Basic Static Radial Load Rating Co:850000 N; Fillet Radius ra:3.00 mm; Fillet Radius rb:1.00 mm; Grease Speed Rating n1:1700 rpm; Basic Dynamic Radial Load Rating C:520000 N; B:140.00 mm; d:110.000 mm; D:320.0000 mm; Oil Speed Rating n2:2100 rpm; |
| 92.20.1246.991.21.1503 Standard 5 Slewing Ring Bearings | D:71.438 mm; Design (sliding contact surface combination):Steel/steel, heavy-d; C:33.325 mm; Specific dynamic load factor K:100 N/mm²; Da min.:61.3 mm; Sealing solution:Triple-lip seals; Basic static load rating C0:510 kN; rb max.:1 mm; da min.:48.5 mm; Da max.:67.4 mm; r1 min.:0.6 mm; Lubricant:Regular relubricatio; Specific static load factor K0:300 N/mm²; d:44.45 mm; ra max.:0.6 mm; da max.:50.7 mm; |
| 12.35.1960.401.41.1503 Standard 5 Slewing Ring Bearings | Cap bolt, SAE grade:5; J max.:333.375 mm; da:88.9 mm; P90°:71.2 kN; Housing:FSAF 520; L:387.35 mm; N1:22.225 mm; Cap bolt recommended tightening torque:203.4 N·m; End plug (suffix Y):EPR 12; J1:60.325 mm; h:42.069 mm; P180°:48.9 kN; PG:1/4 NPT; Initial grease fill:365.71 g; H1:114.3 mm; R2:30.163 mm; P120°:44.5 kN; H:217.488 mm; Stabilizing ring:2 x SR-1520; Da:180 mm; |
| 92.30.1799.991.21.1502 Standard 5 Slewing Ring Bearings | J7:24.5 mm; s1:22.2 mm; N4:4 mm; L:108 mm; Recommended diameter for attachment bolts, mm G:10 mm; A3:3.2 mm; J6:96 mm; J:82.5 mm; Housing:FY 506 M/VZ033; Recommended tightening torque for grub screw:4 N·m; Mass bearing unit:1 kg; Recommended diameter for attachment bolts, inch G:0.375 in; d:30.163 mm; A1:13 mm; A5:20 mm; B:38.1 mm; Hexagonal key size for grub screw N:3.175 mm; Db1:76 mm; Thread grub screw G2:1/4-28 UNF; |
| 162.50.2660.891.41.1503 Standard 5 Slewing Ring Bearings | R2:22.225 mm; PG:1/8 NPT; End plug (suffix Y):EPR 9; RG:3/8 NPT; P120°:23.1 kN; P60°:61.4 kN; H:182.166 mm; h:36.513 mm; H1:95.25 mm; Mass pillow block:16.5 kg; Cap bolt recommended tightening torque:149.1 N·m; R1:53.975 mm; H2:31.75 mm; Initial grease fill:218.29 g; L:330.2 mm; A1:88.9 mm; Housing:FSAF 517; da:71.438 mm; Cap bolt:2 x 5/8-11 UNC; P90°:36.9 kN; |
| 92.50.2266.990.41.1502 Standard 5 Slewing Ring Bearings | s1 max.:25 mm; Operating clearance factor k2:0.099; B2:45 mm; Basic static load rating C0:5000 kN; Ba min.:14 mm; d1:320 mm; D1 ≈:475 mm; B5:58 mm; Fatigue load limit Pu:375 kN; B:133 mm; da max.:425 mm; Basic dynamic load rating C:2900 kN; Reference speed:950 r/min; ra max.:4 mm; Misalignment factor k1:0.12; db min.:355 mm; B1:187 mm; d2 ≈:394 mm; Limiting speed:1300 r/min; Da max.:502 mm; |
| 282.30.1200.013 Type 110/1400.2 Standard 5 Slewing Ring Bearings | Cap bolt:1 1/2-6 UNC; h:79.375 mm; End plug (suffix Y):EPR 23; Stabilizing ring:SR-44-38; A1:222.25 mm; Mass pillow block:365 kg; Cap bolt, SAE grade:8; H2:95.25 mm; Ca:117.805 mm; L:831.85 mm; Eye bolt:2 x 1/2-13 UNC; Initial grease fill:2749.95 g; P90°:414 kN; PosiTrac Plus contact element:2 x B10724-167; PG:1/4 NPT; Cap bolt recommended tightening torque:4284.4 N·m; Da:399.999 mm; da:200.025 mm; |
| No. | Brand | G | J | E | b | A | F | T | U |
| 11.35.2620.001.41.1503 | Standard 5 | - | - | - | - | - | - | - | 12 mm |
| 161.50.2800.891.41.1503 | Standard 5 | 219.151 mm | - | - | - | - | - | - | - |
| 12.50.2559.201.49.1502 | Standard 5 | - | 130 mm | - | - | 34.5 mm | - | - | - |
| 161.45.2366.891.41.1503 | Standard 5 | M 42x3 | - | - | - | - | - | - | - |
| 162.36.2000.890.11.1503 | Standard 5 | - | - | - | - | - | 25 mm | - | - |
| 61.40.1600.008.19.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| 92.35.1704.991.41.1502 | Standard 5 | - | - | - | - | - | - | - | - |
| 62.25.1355.575.11.1403 | Standard 5 | - | - | - | - | - | - | - | - |
| 161.28.1700.890.11.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| 61.40.1400.000.19.1504 | Standard 5 | - | - | - | - | 92.075 mm | - | - | - |
| 162.28.1500.891.21.1503 | Standard 5 | M 130x2 | - | - | - | - | - | - | - |
| 62.25.1255.500.11.1503 | Standard 5 | M16 | - | - | - | - | - | - | - |
| 191.32.2240.990.41.1502 | Standard 5 | - | - | - | - | - | - | - | - |
| 62.50.1800.001.49.1504 | Standard 5 | - | - | - | - | - | - | - | - |
| 92.35.1704.990.11.1502 | Standard 5 | - | - | - | - | - | - | - | - |
| 61.25.1455.575.11.1403 | Standard 5 | - | 670 mm | - | - | - | - | - | - |
| 92.40.2199.990.11.1502 | Standard 5 | M 45x3 | - | - | - | - | - | - | - |
| 91.25.1502.991.21.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| 280.30.1475.013 Type 110/1600. | Standard 5 | - | - | - | 22.3 mm | - | - | - | - |
| 161.45.2654.891.41.1503 | Standard 5 | - | - | - | 1.4 mm | - | - | - | - |
161.50.2800.891.41.1503 Standard 5 Slewing Ring Bearings Video
161.50.2800.891.41.1503 Drawing of Rothe Erde slewing bearing
161.50.2800.891.41.1503. Size：; Language： English; Categories： Drawing; Download. Copyright @2002-2012 Luoyang JCB Bearing Technology Co., Ltd | All
161.50.2800.891.41.1503 of Rothe Erde slewing bearing
Jul 24, 2014 - 161.50.2800.891.41.1503 of Rothe Erde slewing bearing. We are Luoyang JCB Bearing Technology Company, working on industry of slewing
Buy 161.50.2800.891.41.1503 Rothe erde slewing ring - Wanda
Buy 161.50.2800.891.41.1503 Rothe erde slewing ring from Wanda Slewing Bearing Supplier，Thyssenkrupp Rotary Slewing Bearing Distributor online Service
161.50.2800.891.41.1503 Rothe Erde Slewing Ring Bearings | Lily
We supply 161.50.2800.891.41.1503 slewing ring to customer according to Rothe Erde standard and specification, the quality of our product is same as original
Buy 161.50.2800.891.41.1503 slewing rings without gear - RT
Buy 161.50.2800.891.41.1503 slewing rings without gear from RT BEARINGS PTV.LTD，thyssenkrupp rothe erde slewing bearing Distributor online Service
161.50.2800.891.41.1503 slewing ring bearings with ... - JCB Bearing
Page 1. Luoyang JCB Bearing Technology Co., Ltd
Rothe Erde Slewing Bearing Luoyang JCB Bearing Import
161.45.2654.891.41.1503 161.50.2660.891.41.1503 161.50.2800.891.41.1503 161.50.3000.891.41.1503. Bearing with internal gear 162.16.0400.890.11.1503
TIMKEN slewing bearing of page 36
161.50.2800.891.41.1503 Rothe erde slewing ring: Brand Name : thk: Model Number : 2565. 161.45.2654.891.41.1503 slewing rings without gear: Model
Product Categories - SJC slewing bearing Inc of page 65
161.50.2800.891.41.1503 Rothe erde slewing ring: Brand Name : thk: Model Number : 2565. 280.30.1200.013 Type 110/1400.0 Rothe erde slewing bearing
Cross Roller Slewing Bearing Ring Bearing 161.50.2800.891.41.1503
China Cross Roller Slewing Bearing Ring Bearing 161.50.2800.891.41.1503, Find details about China Slewing Bearing, Slewing Bearings from Cross Roller