| 60.25.1455.500.11.1503 Standard 5 Slewing Ring Bearings | d:12 mm; Mass inner ring:0.0079 kg; F:16 mm; B:12 mm; r, r1,2 min.:0.3 mm; |
| 192.25.1800.990.41.1502 Standard 5 Slewing Ring Bearings | Ca min.:2.3 mm; Fatigue load limit Pu:520 kN; s1 max.:33.5 mm; Da min.:604 mm; B2:60 mm; d3:540 mm; B:163 mm; Mass bearing + sleeve:270 kg; db min.:478 mm; Limiting speed:950 r/min; D:680 mm; da max.:570 mm; Misalignment factor k1:0.114; r1,2 min.:6 mm; Basic dynamic load rating C:4000 kN; Da max.:657 mm; d1:430 mm; Ba min.:17 mm; d2 ≈:539 mm; B1:234 mm; |
| 12.40.2199.300.11.1502 Standard 5 Slewing Ring Bearings | B:243 mm; Reference speed:530 r/min; D:520 mm; das:384 mm; Mass bearing:185 kg; Limiting speed:670 r/min; s max.:11 mm; d:340 mm; d1 ≈:395 mm; rb max.:4 mm; K:5 mm; Fatigue load limit Pu:710 kN; Da max.:500 mm; Basic dynamic load rating C:4400 kN; r1,2 min.:5 mm; da min.:362 mm; b1:9.4 mm; D1 ≈:468 mm; Basic static load rating C0:8300 kN; Calculation factor kr:0.5; |
| 191.40.2800.990.41.1502 Standard 5 Slewing Ring Bearings | Weight W:0.84 lb; ZZ:0.06 in; Basic Dynamic Radial Load Rating:5730 lbf; D_SEL:5/16-24; Diameter D3:1.815 in; Outher Width C:0.7480 in; Bore Diameter D:1 7/16 in; TP:0.02 in; ANGLE:135 º; Outside Diameter D2:2.8346 in; Inner Width B:1.688 in; D11:1.815 in; Basic Static Radial Load Rating Co:3440 lbf; Dimension S:0.689 in; |
| 11.30.1440.191.41.1503 Standard 5 Slewing Ring Bearings | r1 min.:2 mm; r2 min.:5 mm; D:680 mm; Basic static load rating C0:21200 kN; Basic dynamic load rating C:14300 kN; Da max.:641 mm; α:2 °; rb max.:5 mm; Specific static load factor K0:120 N/mm²; da min.:503 mm; Specific dynamic load factor K:80 N/mm²; b1:27 mm; b:27 mm; C:320 mm; ra max.:2 mm; Design (sliding contact surface combination):Steel/PTFE FRP; B:340 mm; da max.:522 mm; Da min.:580 mm; |
| 11.35.2220.001.41.1503 Standard 5 Slewing Ring Bearings | R2:21.431 mm; N1:15.875 mm; RG:1/4 NPT; S:3.175 mm; P120°:28.5 kN; End plug (suffix Y):EPR 8; P180°:30.7 kN; h:28.575 mm; J min.:215.9 mm; db:87.313 mm; H1:82.55 mm; dc:71.438 mm; Stabilizing ring:SR-15-0; Housing:FSAFS 215; H:161.925 mm; Taconite seal (db shaft position):TER 79; Appropriate attachment bolt size G:0.5 in; da:75 mm; Initial grease fill:68.04 g; ba:32.544 mm; |
| 161.36.1800.891.41.1503 Standard 5 Slewing Ring Bearings | Initial grease fill:136.08 g; Housing:SAF 515; ba:30.163 mm; H1:82.55 mm; h:31.75 mm; Pa:5.65 kN; P60°:75.6 kN; Stabilizing ring:2 x SR-15-0; P180°:30.2 kN; N1:19.05 mm; P120°:28 kN; L:285.75 mm; da:61.913 mm; Da:130 mm; Mass pillow block:13.1 kg; A1:79.375 mm; Max. speed for Taconite seal:1250 r/min; P90°:45.4 kN; A2:193.675 mm; J max.:244.475 mm; |
| 92.30.1799.990.11.1502 Standard 5 Slewing Ring Bearings | Basic dynamic load rating C:59.5 kN; ra max.:3.6 mm; B:19.05 mm; da max.:38 mm; Mass bearing:0.24 kg; Ca min.:4 mm; Db min.:58 mm; r3,4 min.:2 mm; a:12.68 mm; T:18.161 mm; Calculation factor e:0.35; Cb min.:3.5 mm; d1 ≈:45.79 mm; Basic static load rating C0:57 kN; Da min.:54 mm; d:31.75 mm; C:14.288 mm; Reference speed:9000 r/min; r1,2 min.:3.6 mm; db min.:44 mm; |
| 191.25.2500.990.41.1502 Standard 5 Slewing Ring Bearings | A:73.025 mm; H1:69.85 mm; J max.:222.25 mm; s:32.941 mm; Limiting speed:3100 r/min; B:65.484 mm; S:0.794 mm; L:266.7 mm; J min.:209.55 mm; Basic dynamic load rating C:193 kN; Mass bearing unit:8.39 kg; H:144.463 mm; H2:41.275 mm; Attachment bolt diameter G:15.875 mm; da:63.5 mm; |
| 12.30.1995.001.41.1503 Standard 5 Slewing Ring Bearings | h:36.513 mm; R2:19.05 mm; H1:76.2 mm; PG:1/8 NPT; J min.:196.85 mm; RG:1/8 NPT; H:147.637 mm; Initial grease fill:107.73 g; A1:69.85 mm; N1:19.05 mm; Stabilizing ring:2 x SR-1610; Mass pillow block:10 kg; Cap bolt, SAE grade:8; Cap bolt:2 x 1/2-13 UNC; H2:28.575 mm; P90°:23.6 kN; Da:110 mm; Cap bolt recommended tightening torque:149.1 N·m; R1:42.862 mm; P180°:15.6 kN; |
| 12.25.1600.000.11.1503 Standard 5 Slewing Ring Bearings | Basic Static Radial Load Rating Co:102000 N; Fillet Radius ra:2.00 mm; D:150.0000 mm; B:35.00 mm; d:70.000 mm; Oil Speed Rating Open/Shielded n2:4500 rpm; Basic Dynamic Radial Load Rating C:114000 N; Accessories:One Shield & Snap-Ri; Grease Speed Rating Open/Shielded n1:3700 rpm; |
| 162.25.1250.891.21.1503 Standard 5 Slewing Ring Bearings | Initial grease fill:481.95 g; Pa:82.3 kN; J1:85.725 mm; RG:3/4 NPT; Ca:77.8 mm; Cap bolt recommended tightening torque:813.5 N·m; P180°:127 kN; H:298.45 mm; H2:60.325 mm; A2:260.35 mm; h:51.594 mm; db:158.75 mm; da:140 mm; Mass pillow block:85.3 kg; P90°:180 kN; dc:134.938 mm; P150°:105 kN; PG:1/4 NPT; P120°:116 kN; Cap bolt, SAE grade:8; |
| 92.40.2395.990.11.1502 Standard 5 Slewing Ring Bearings | Permissible sliding velocity v max.:0.5 m/s; Permissible sliding velocity v min.:0 m/s; B:300 mm; Tolerance shaft:e7; h:202.5 mm; a:15 mm; Tolerance housing:H7; d:200 mm; Coefficient of friction µ max.:0.15; Mass bushing:17.4 kg; Coefficient of friction µ min.:0.08; α:124 °; D:220 mm; Specific dynamic load factor K:25 N/mm²; Specific static load factor K0:45 N/mm²; |
| 62.30.1600.001.21.1504 Standard 5 Slewing Ring Bearings | G1:32 mm; G2:G 1/4; A:9 mm; B2:363 mm; d1:460 mm; G:Tr 500x5; Hydraulic nut:HMV 100 E; B1:340 mm; d:480 mm; Mass withdrawal sleeve:51.5 kg; |
| 11.35.2220.000.11.1503 Standard 5 Slewing Ring Bearings | Oil level, min.:81 mm; Mass housing:454 kg; Da:600 mm; Eye bolt, size:2 x M 36; Cap bolt, rec. tightening torque:600 N·m; ba min.:145 mm; Oil level, max.:98 mm; Appropriate attachment bolt, size G:36 mm; H2:120 mm; P150°:2400 kN; s:30 mm; Oil seal:TSD 3080 U; J:840 mm; P0°:6000 kN; J1:220 mm; Cap bolt, size:M 36x240; Q180°:2100 kN; bb:140 mm; H:695 mm; P90°:3600 kN; |
| 91.20.1246.991.21.1503 Standard 5 Slewing Ring Bearings | Ca:55.804 mm; H:217.488 mm; R2:30.163 mm; Pa:16.7 kN; A1:111.125 mm; Cap bolt:2 x 3/4-10 UNC; Mass pillow block:28.6 kg; A2:228.6 mm; ba:46.831 mm; J1:60.325 mm; Max. speed for Taconite seal:725 r/min; Stabilizing ring:2 x 38151-24; J max.:333.375 mm; H2:44.45 mm; P90°:71.2 kN; Appropriate attachment bolt size G:0.75 in; P120°:44.5 kN; J min.:295.275 mm; N1:22.225 mm; H1:114.3 mm; |