| 91.50.2446.990.41.1502 Standard 5 Slewing Ring Bearings | B:17 mm; d:15 mm; D:17 mm; Permissible sliding velocity v min.:0 m/s; Tolerance housing:H7; Permissible sliding velocity v max.:1 m/s; B1:1 mm; Specific static load factor K0:80 N/mm²; Mass bushing:0.0016 kg; Coefficient of friction µ max.:0.15; Specific dynamic load factor K:40 N/mm²; D1:23 mm; Tolerance shaft:h9; Coefficient of friction µ min.:0.06; |
| 12.30.1995.001.41.1503 Standard 5 Slewing Ring Bearings | h:36.513 mm; R2:19.05 mm; H1:76.2 mm; PG:1/8 NPT; J min.:196.85 mm; RG:1/8 NPT; H:147.637 mm; Initial grease fill:107.73 g; A1:69.85 mm; N1:19.05 mm; Stabilizing ring:2 x SR-1610; Mass pillow block:10 kg; Cap bolt, SAE grade:8; Cap bolt:2 x 1/2-13 UNC; H2:28.575 mm; P90°:23.6 kN; Da:110 mm; Cap bolt recommended tightening torque:149.1 N·m; R1:42.862 mm; P180°:15.6 kN; |
| 11.30.1734.001.41.1503 Standard 5 Slewing Ring Bearings | Basic Static Radial Load Rating Co:19300 N; Basic Dynamic Radial Load Rating C:63700 N; D:100.0000 mm; B:36.00 mm; Oil Speed Rating n2:6700 rpm; Grease Speed Rating n1:5600 rpm; Fillet Radius ra:1.50 mm; d:45.000 mm; |
| 61.40.1400.001.29.1504 Standard 5 Slewing Ring Bearings | Taconite seal:TER 53; Da:150 mm; S:4.763 mm; Cap bolt recommended tightening torque:298.3 N·m; Housing:SAFS 517; h:34.925 mm; Appropriate attachment bolt size G:0.75 in; Pa:9.25 kN; Ca:45.796 mm; P90°:47.2 kN; Stabilizing ring:SR-17-14; da:74.612 mm; Max. speed for Taconite seal:1050 r/min; H2:38.1 mm; J min.:250.825 mm; R1:53.975 mm; P180°:32 kN; Mass pillow block:24.5 kg; Cap bolt:2 x 5/8-11 UNC; |
| 61.25.1155.500.11.1503 Standard 5 Slewing Ring Bearings | B:185 mm; s1 max.:35.7 mm; B2:90 mm; D:1000 mm; Mass bearing + sleeve:590 kg; d1:710 mm; db min.:772 mm; d3:870 mm; da max.:856 mm; Reference speed:430 r/min; d2 ≈:830 mm; ra max.:5 mm; Da min.:908 mm; B5:112 mm; Basic static load rating C0:13400 kN; Operating clearance factor k2:0.101; r1,2 min.:6 mm; Misalignment factor k1:0.131; Limiting speed:560 r/min; D1 ≈:934 mm; |
| 60.25.1355.500.11.1503 Standard 5 Slewing Ring Bearings | h:38.1 mm; End plug (suffix Y):EPR 11; J min.:263.525 mm; H1:101.6 mm; A2:149.225 mm; Cap bolt:4 x 5/8-11 UNC; db:104.775 mm; ba:40.481 mm; Cap bolt, SAE grade:8; Appropriate attachment bolt size G:0.75 in; P90°:84.5 kN; H2:41.275 mm; Pa:37.8 kN; Cap bolt recommended tightening torque:298.3 N·m; P60°:141 kN; PG:1/8 NPT; Da:160 mm; Bearing limiting speed:5300 r/min; N1:23.813 mm; J max.:295.275 mm; |
| 91.30.1799.991.21.1502 Standard 5 Slewing Ring Bearings | Mass adapter sleeve assembly:59.5 kg; B:60.579 mm; B1:231.14 mm; G:438.988 mm; d1:419.1 mm; Hydraulic nut:HMVC 88E; Threads per inch:5; Sleeve:S 3088x16.1/2; d:440 mm; d3 max.:520.827 mm; B5:73.812 mm; |
| 92.40.2003.990.11.1502 Standard 5 Slewing Ring Bearings | Hydraulic nut:HMVC 15E; d:75 mm; d3 max.:98.552 mm; Threads per inch:12; d1:63.5 mm; Mass adapter sleeve assembly:1.35 kg; Sleeve:S 115x2.1/2; B1:78.08 mm; B:15.342 mm; G:74.498 mm; B4:16.916 mm; |
| 161.25.1320.890.11.1503 Standard 5 Slewing Ring Bearings | d:190.000 mm; Basic Dynamic Radial Load Rating C:242000 N; Fillet Radius ra:2.50 mm; B:46.00 mm; Oil Speed Rating n2:2400 rpm; Grease Speed Rating n1:1400 rpm; Basic Static Radial Load Rating Co:315000 N; D:300.0000 mm; Fillet Radius rb:1.00 mm; |
| 92.35.1900.991.41.1502 Standard 5 Slewing Ring Bearings | r1,2 min.:2 mm; d:120 mm; Reference speed:4000 r/min; da max.:133 mm; Axial load factor Y:0.6; D1 ≈:158.85 mm; Limiting value e:0.2; s max.:3.8 mm; ra max.:2 mm; Mass bearing:2.47 kg; r3,4 min.:1.1 mm; rb max.:1 mm; db min.:138 mm; Da max.:171 mm; F:135 mm; Fatigue load limit Pu:20.8 kN; Basic static load rating C0:183 kN; D:180 mm; B:28 mm; Limiting speed:4000 r/min; |
| 162.25.1320.890.11.1503 Standard 5 Slewing Ring Bearings | Grub screws:3 x M 6; J6:185 mm; Attachment bolt diameter G:12 mm; H1:60 mm; Grease quantity for relubrication:3 g; A:60 mm; N:20 mm; P120°:95 kN; Limiting speed:2050 r/min; L:205 mm; Calculation factor Y1:2.2; Pa:15 kN; P0°:150 kN; Mass bearing unit:3.8 kg; Tightening torque for attachment bolts:80 N·m; J:170 mm; P55°:250 kN; Basic static load rating C0:85 kN; H2:25 mm; J7:21 mm; |
| 162.28.1600.890.11.1503 Standard 5 Slewing Ring Bearings | D:250.0000 mm; Oil Speed Rating Open/Shielded n2:3300 rpm; Basic Dynamic Radial Load Rating C:203000 N; Grease Speed Rating Open/Shielded n1:2700 rpm; Accessories:Two Shields; d:95.000 mm; Sealed Speed Rating n3:1900 rpm; B:55.00 mm; Fillet Radius ra:3.00 mm; Basic Static Radial Load Rating Co:173000 N; |
| 192.20.1400.990.41.1502 Standard 5 Slewing Ring Bearings | Grease Speed Rating Open/Shielded n1:5000 rpm; Fillet Radius ra:1.00 mm; Basic Static Radial Load Rating Co:31500 N; B:18.00 mm; Sealed Speed Rating n3:3100 rpm; D:125.0000 mm; Oil Speed Rating Open/Shielded n2:6000 rpm; Basic Dynamic Radial Load Rating C:32500 N; d:90.000 mm; Accessories:Two Shields; |
| 60.25.1255.575.11.1403 Standard 5 Slewing Ring Bearings | B4:23.012 mm; Threads per inch:12; Hydraulic nut:HMVC 22E; d1:98.425 mm; Mass adapter sleeve assembly:2.95 kg; d:110 mm; Sleeve:S 122x3.7/8; B1:110.185 mm; G:109.855 mm; B:20.091 mm; d3 max.:145.39 mm; |
| 92.30.1799.990.11.1502 Standard 5 Slewing Ring Bearings | Basic dynamic load rating C:59.5 kN; ra max.:3.6 mm; B:19.05 mm; da max.:38 mm; Mass bearing:0.24 kg; Ca min.:4 mm; Db min.:58 mm; r3,4 min.:2 mm; a:12.68 mm; T:18.161 mm; Calculation factor e:0.35; Cb min.:3.5 mm; d1 ≈:45.79 mm; Basic static load rating C0:57 kN; Da min.:54 mm; d:31.75 mm; C:14.288 mm; Reference speed:9000 r/min; r1,2 min.:3.6 mm; db min.:44 mm; |
| 91.35.1802.990.11.1502 Standard 5 Slewing Ring Bearings | J min.:406.4 mm; ba:61.119 mm; Initial grease fill:481.95 g; Eye bolt:2 x 3/8-16 UNC; Bearing limiting speed:3200 r/min; Da:250 mm; S:4.763 mm; J max.:434.975 mm; Labyrinth ring:2 x LOR 121; N1:28.575 mm; P90°:180 kN; A1:149.225 mm; PG:1/4 NPT; Ca:77.8 mm; J1:85.725 mm; P150°:105 kN; Appropriate attachment bolt size G:1 in; End plug (suffix Y):EPR 27; Pa:28.5 kN; h:51.594 mm; |
| No. | Brand | G | J | E | b | A | F | T | U |
| 162.45.2366.890.11.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| 161.28.1700.890.11.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| 162.40.2000.891.41.1503 | Standard 5 | Tr 500x5 | - | - | - | - | - | - | - |
| 61.30.1500.200.11.1504 | Standard 5 | - | - | - | - | - | - | - | - |
| 162.50.2500.891.41.1503 | Standard 5 | 169.139 mm | - | - | - | - | - | - | - |
| 282.30.1375.013 Type 110/1500.2 | Standard 5 | - | - | - | - | - | - | - | - |
| 161.50.2800.891.41.1503 | Standard 5 | 219.151 mm | - | - | - | - | - | - | - |
| 62.40.1500.001.29.1504 | Standard 5 | - | - | - | - | - | - | 334.962 mm | - |
| 91.30.1799.990.11.1502 | Standard 5 | - | - | - | - | - | - | - | - |
| 11.25.1461.001.21.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| 162.40.2368.890.11.1503 | Standard 5 | - | - | - | 22.3 mm | - | - | - | - |
| 61.40.1600.009.29.1503 | Standard 5 | M 55x2 | - | - | 7 mm | - | - | - | - |
| 61.25.1255.575.11.1403 | Standard 5 | Tr 750x7 | - | - | - | 12 mm | - | - | - |
| 162.45.2654.890.11.1503 | Standard 5 | - | - | - | - | - | - | - | 20 mm |
| 62.25.1455.500.11.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| 191.20.1250.990.41.1502 | Standard 5 | - | - | - | - | - | - | 64.4 mm | - |
| 92.30.1799.991.21.1502 | Standard 5 | - | 82.5 mm | - | - | - | - | - | - |
| 280.30.1475.013 Type 110/1600. | Standard 5 | - | - | - | 22.3 mm | - | - | - | - |
| 91.30.1415.990.11.1502 | Standard 5 | - | - | - | - | - | - | - | - |
| 62.40.1500.000.19.1504 | Standard 5 | - | - | - | - | - | - | - | - |
| 91.35.1900.990.11.1502 | Standard 5 | - | - | - | - | - | - | - | - |
| 161.36.1700.890.11.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| 91.35.1704.990.11.1502 | Standard 5 | - | - | - | - | - | - | - | - |
| 161.45.2240.890.11.1503 | Standard 5 | M 45x3 | - | - | - | - | - | - | - |
| 282.30.1400.013 Type 110/1600.2 | Standard 5 | - | - | - | - | - | - | 701.675 mm | - |
| 162.50.2660.891.41.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| 161.25.1250.891.21.1503 | Standard 5 | - | - | - | - | - | - | - | - |
91.35.2012.990.11.1502 Standard 5 Slewing Ring Bearings Video
091.35.2012.990.11.1502 - Slewing Ring Bearings Manufacturers ...
LYMC bearings are the perfect alternative to the most common and well-known brands.