| 92.35.1704.991.41.1502 Standard 5 Slewing Ring Bearings | B:56.00 mm; Oil Speed Rating Open/Shielded n2:1600 rpm; Sealed Speed Rating n3:800 rpm; Fillet Radius ra:3.00 mm; Accessories:Without Accessories; d:300.000 mm; Basic Static Radial Load Rating Co:375000 N; Basic Dynamic Radial Load Rating C:270000 N; Grease Speed Rating Open/Shielded n1:1300 rpm; D:420.0000 mm; |
| 12.20.1360.000.11.1504 Standard 5 Slewing Ring Bearings | J min.:131.762 mm; Mass bearing unit:3.65 kg; A:58.737 mm; H1:53.975 mm; J max.:152.4 mm; Basic dynamic load rating C:102 kN; H2:33.337 mm; L:187.325 mm; Limiting speed:4500 r/min; s:29.766 mm; S:0.794 mm; Attachment bolt diameter G:12.7 mm; B:59.531 mm; H:109.537 mm; da:42.862 mm; |
| 162.40.2240.891.41.1503 Standard 5 Slewing Ring Bearings | B:34.00 mm; d:100.000 mm; Grease Speed Rating n1:3400 rpm; Grease Speed Rating Open/Shielded n1:3400 rpm; D:180.0000 mm; Accessories:One Seal; Oil Speed Rating n2:4000 rpm; Sealed Speed Rating n3:2400 rpm; Basic Static Radial Load Rating Co:93000 N; Fillet Radius ra:2.00 mm; Basic Dynamic Radial Load Rating C:124000 N; Oil Speed Rating Open/Shielded n2:4000 rpm; |
| 281.30.1275.013 Type 110/1400.1 Standard 5 Slewing Ring Bearings | Oil Speed Rating n2:3400 rpm; D:170.0000 mm; Grease Speed Rating n1:2400 rpm; Fillet Radius ra:2.00 mm; Sealed Speed Rating n3:2400 rpm; d:80.000 mm; Basic Dynamic Radial Load Rating C:182000 N; Basic Static Radial Load Rating Co:156000 N; B:68.30 mm; Accessories:Two Shields & Snap-R; |
| 192.40.2800.990.41.1502 Standard 5 Slewing Ring Bearings | Coefficient of friction µ min.:0.08; Mass bushing:9.68 kg; α:124 °; Specific dynamic load factor K:25 N/mm²; a:7 mm; B:140 mm; Tolerance shaft:e7; Permissible sliding velocity v min.:0 m/s; D:260 mm; Permissible sliding velocity v max.:0.5 m/s; Coefficient of friction µ max.:0.15; d:240 mm; h:242.5 mm; Specific static load factor K0:45 N/mm²; Tolerance housing:H7; |
| 91.30.1415.991.21.1502 Standard 5 Slewing Ring Bearings | Thread grub screw G2:1/4-28 UNF; J:116.5 mm; Limiting speed:6300 r/min; Rα:45 °; N:11.5 mm; Fatigue load limit Pu:0.475 kN; DN:6.5 mm; d:30.163 mm; B:30.2 mm; Basic static load rating C0:11.2 kN; B4:5 mm; Housing material:Cast iron; J6:98.5 mm; Recommended diameter for attachment bolts, mm G:10 mm; N4:2 mm; Basic dynamic load rating C:19.5 kN; s1:21 mm; L:83 mm; A3:3.2 mm; R1:21 mm; |
| 12.30.1381.000.11.1503 Standard 5 Slewing Ring Bearings | Mass rod end:15 kg; Basic static load rating C0:655 kN; G:M 80x4; d4 ≈:105 mm; d:80 mm; r1 min.:1 mm; d2 max.:182 mm; h1:295 mm; α:5 °; l5 ≈:45 mm; w:90 mm; dk:105 mm; Specific dynamic load factor K:100 N/mm²; C1 max.:48 mm; l3 min.:85 mm; Basic dynamic load rating C:400 kN; Material constant KM:330; B:55 mm; l4 max.:389 mm; l7 min.:88 mm; |
| 162.45.2510.890.11.1503 Standard 5 Slewing Ring Bearings | Basic dynamic load rating C:12.7 kN; H1:76 mm; Limiting speed with shaft tolerance h6:5000 r/min; H:89 mm; s1:18.3 mm; Basic static load rating C0:6.55 kN; A1:12 mm; d:19.05 mm; G:M16; G1:21 mm; Recommended tightening torque for grub screw:4 N·m; Grub (set) screw G2:1/4-28 UNF; B:31 mm; L1:64 mm; Hexagonal key size for grub screw N:3.175 mm; A:27.5 mm; L:99 mm; Housing material:Composite for food a; |
| 282.30.1475.013 Type 110/1600.2 Standard 5 Slewing Ring Bearings | B:368 mm; r1,2 min.:2 mm; Design variant/feature:TQON/GW; Calculation factor Y2:3.4; Mass bearing:250 kg; Basic static load rating C0:16600 kN; T:368 mm; Calculation factor Y0:2.2; Fatigue load limit Pu:1250 kN; r3,4 min.:6 mm; Basic dynamic load rating C:5720 kN; Thrust factor K:2.03; Comparative axial load rating CFa:200 kN; D1 ≈:554 mm; Calculation factor e:0.3; d:475 mm; d1 ≈:500 mm; |
| 162.40.2240.890.11.1503 Standard 5 Slewing Ring Bearings | Accessories:One Seal; d:25.000 mm; Oil Speed Rating n2:11000 rpm; B:20.60 mm; Fillet Radius ra:1.00 mm; Grease Speed Rating n1:8000 rpm; Sealed Speed Rating n3:8000 rpm; Basic Dynamic Radial Load Rating C:22900 N; Basic Static Radial Load Rating Co:21200 N; D:52.0000 mm; |
| 91.40.2199.991.41.1502 Standard 5 Slewing Ring Bearings | D:8 mm; Limiting speed:85000 r/min; Basic static load rating C0:0.061 kN; Mass bearing:0.0003 kg; D1 ≈:7.25 mm; B:2 mm; d1 ≈:5.75 mm; r1,2 min.:0.1 mm; ra max.:0.1 mm; Fatigue load limit Pu:0.003 kN; Reference speed:140000 r/min; Calculation factor f0:7.7; Da max.:7.4 mm; da min.:5.6 mm; d:5 mm; Basic dynamic load rating C:0.174 kN; Calculation factor kr:0.015; |
| 62.25.1255.500.11.1503 Standard 5 Slewing Ring Bearings | Mass bearing unit:0.6 kg; H2:40 mm; Grub (set) screw G2:1/4-28 UNF; Basic static load rating C0:11.2 kN; H:102.5 mm; B:38.1 mm; d:31.75 mm; s1:22.2 mm; L1:76 mm; B4:5 mm; H1:89 mm; Housing material:Composite for food a; Recommended tightening torque for grub screw:4 N·m; Fatigue load limit Pu:0.475 kN; L:125 mm; A1:12 mm; G:M16; A5:26.5 mm; A2:30 mm; G1:21 mm; |
| 12.30.1995.000.11.1503 Standard 5 Slewing Ring Bearings | d:90 mm; Specific static load factor K0:20 N/mm²; Permissible sliding velocity v min.:0.25 m/s; B:80 mm; Tolerance housing:H7; Coefficient of friction µ min.:0.05; Mass bushing:1.16 kg; Tolerance shaft:h8; Permissible sliding velocity v max.:5 m/s; Coefficient of friction µ max.:0.1; Specific dynamic load factor K:10 N/mm²; D:105 mm; |
| 62.25.1355.575.11.1403 Standard 5 Slewing Ring Bearings | Mass shaft washer:0.5 kg; B:17 mm; d:75 mm; r1,2 min.:2 mm; d1:160 mm; |
| 61.50.1900.001.49.1504 Standard 5 Slewing Ring Bearings | da:177.8 mm; J1:114.3 mm; PG:1/4 NPT; Cap bolt recommended tightening torque:271.2 N·m; RG:1 NPT; J min.:549.275 mm; Pa:52.5 kN; Eye bolt:2 x 1/2-13 UNC; Housing:SAF 538; Da:339.999 mm; A1:190.5 mm; S:4.763 mm; L:711.2 mm; End plug (suffix Y):EPR 21; Appropriate attachment bolt size G:1.25 in; J max.:619.125 mm; ba:78.581 mm; R1:120.65 mm; P60°:290 kN; PosiTrac Plus contact element:2 x B10724-155; |
| 12.40.2950.000.11.1502 Standard 5 Slewing Ring Bearings | Permissible sliding velocity v min.:0 m/s; Mass bushing:0.97 kg; Coefficient of friction µ max.:0.08; B:150 mm; D:140 mm; Effective load carrying cross section A:20720 mm²; Tolerance shaft:h8; Specific dynamic load factor K:140 N/mm²; Tolerance housing:H7; Coefficient of friction µ min.:0.03; d:155 mm; Specific static load factor K0:200 N/mm²; Permissible sliding velocity v max.:0.5 m/s; |
| No. | Brand | G | J | E | b | A | F | T | U |
| 91.40.2003.990.11.1502 | Standard 5 | - | - | - | - | 80.963 mm | - | - | - |
| 191.32.2240.990.41.1502 | Standard 5 | - | - | - | - | - | - | - | - |
| 60.25.1455.500.11.1503 | Standard 5 | - | - | - | - | - | 16 mm | - | - |
| 92.50.2446.990.41.1502 | Standard 5 | - | - | - | - | - | - | - | - |
| 162.40.2240.891.41.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| 161.25.1250.891.21.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| 61.30.1320.001.21.1504 | Standard 5 | - | - | - | - | - | - | - | - |
| 162.45.2654.891.41.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| 12.35.1960.401.41.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| 192.20.2000.990.41.1502 | Standard 5 | - | - | - | - | - | - | - | - |
| 91.35.1900.990.11.1502 | Standard 5 | - | - | - | - | - | - | - | - |
| 192.25.2000.990.41.1502 | Standard 5 | - | - | 1161 mm | 22.3 mm | - | - | - | - |
| 61.25.1155.500.11.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| 91.20.1246.990.11.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| 11.40.2795.001.41.1502 | Standard 5 | - | - | - | - | - | - | - | - |
| 162.36.1800.891.41.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| 162.25.1320.890.11.1503 | Standard 5 | - | 170 mm | - | - | 60 mm | - | - | - |
| 161.25.1320.891.21.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| 11.25.1200.601.21.1503 | Standard 5 | - | - | - | 22.3 mm | - | - | - | - |
| 281.30.1475.013 Type 110/1600.1 | Standard 5 | - | - | - | - | - | - | - | - |
| 162.45.2366.891.41.1503 | Standard 5 | - | - | - | - | - | - | - | - |
162.36.1700.891.41.1503 Standard 5 Slewing Ring Bearings Video
162.36.1700.891.41.1503 | Lily Bearing
Part Number, 162.36.1700.891.41.1503. Permissibe tangential forces,normal(X1). Permissibe tangential forces,maximum(X2). Outline Dimensions and Weight
Buy 162.36.1700.891.41.1503 Four-point contact ball slewing rings
Buy 162.36.1700.891.41.1503 Four-point contact ball slewing rings from Wanda Slewing Bearing Supplier，Thyssenkrupp Rotary Slewing Bearing Distributor
Buy 162.36.1700.891.41.1503 thyssenkrupp rothe erde
Buy 162.36.1700.891.41.1503 thyssenkrupp rothe erde slewing bearing from PT GREAT MACHINE ENGINEERING，Cylindrical roller slewing bearing
162.36.1700.891.41.1503 thyssenkrupp rothe erde slewing
162.36.1700.891.41.1503 thyssenkrupp rothe · erde slewing bearing. Bearing No. 510011. Size. 48x89x44 mm. Bore Diameter. 48 mm. Outer Diameter. 89 mm
Rothe erde slewing bearing standard RD800
162.36.1700.891.41.1503, 1700, 636, 1871, 1456, 100. 162.36.1800.890.11.1503, 1800, 675, 1971, 1554, 100. 162.36.1800.891.41.1503, 1800, 675, 1971
Rothe Erde slewing bearing Luoyang JCB Bearing
1871. 1456. 100. 162.36.1700.891.41.1503 · 162.36.1800.890.11.1503. 675. 1971. 1554. 100. 162.36.1800.891.41.1503 · 162.36.1900.890.11.1503. 720. 2071
162.36.1700.891.41.1503 slewing ring bearings with ... - JCB Bearing
Page 1. Luoyang JCB Bearing Technology Co., Ltd
Series 16 | Lily Bearing
162.36.1700.891.41.1503 · 162.36.1800.891.41.1503 · 162.36.1900.891.41.1503 · 162.36.2000.891.41.1503 · 161.40.2000.891.41.1503 · 161.40.2128.891
Buy 162.36.1700.891.41.1503 Rothe erde slewing bearing
Buy 162.36.1700.891.41.1503 Rothe erde slewing bearing from HongKong EVEN Slewing Bearing Co,.Ltd，RKS Series Slewing Bearing Distributor online
KD 700 Series Rothe Erde slewing ring bearing , excavator
162.36.1700.890.11.1503,162.36.1700.891.41.1503,162.36.1800.890.11.1503. 162.36.1800.891.41.1503,162.36.1900.890.11.1503,162.36.1900.891.41.1503