| 11.20.1385.000.11.1504 Standard 5 Slewing Ring Bearings | Eye bolt:2 x 3/8-16 UNC; ba:82.55 mm; Stabilizing ring:SR-32-0; Da:289.999 mm; Pa:49.8 kN; Initial grease fill:793.8 g; P120°:85.9 kN; H2:66.675 mm; P180°:94.3 kN; R2:33.337 mm; Labyrinth ring:2 x LOR 131; P90°:136 kN; Mass pillow block:109 kg; End plug (suffix Y):EPR 16; H:336.55 mm; RG:3/4 NPT; P60°:226 kN; A1:158.75 mm; Cap bolt:4 x 3/4-10 UNC; A2:223.838 mm; |
| 92.50.2644.990.41.1502 Standard 5 Slewing Ring Bearings | Da min.:52.3 mm; ra max.:0.6 mm; Specific static load factor K0:300 N/mm²; b1:5 mm; Design (sliding contact surface combination):Steel/steel; D:61.913 mm; r1 min.:0.6 mm; dk:54.737 mm; M:4 mm; Lubricant:Regular relubricatio; da max.:43.4 mm; b:4.8 mm; Basic static load rating C0:375 kN; α:6 °; r2 min.:1 mm; B:33.325 mm; Da max.:58 mm; Sealing solution:Triple-lip seals; Basic dynamic load rating C:125 kN; |
| 282.30.1300.013 Type 110/1500.2 Standard 5 Slewing Ring Bearings | Permissible sliding velocity v max.:5 m/s; Mass bushing:0.002 kg; D:11 mm; Permissible sliding velocity v min.:0.25 m/s; Coefficient of friction µ max.:0.1; Tolerance housing:H7; d:8 mm; Coefficient of friction µ min.:0.05; Tolerance shaft:h8; B:6 mm; Specific dynamic load factor K:10 N/mm²; Specific static load factor K0:20 N/mm²; |
| 162.36.2000.891.41.1503 Standard 5 Slewing Ring Bearings | Oil Speed Rating n2:5300 rpm; Grease Speed Rating Open/Shielded n1:4500 rpm; Oil Speed Rating Open/Shielded n2:5300 rpm; Fillet Radius ra:2.00 mm; B:26.00 mm; Grease Speed Rating n1:4500 rpm; Sealed Speed Rating n3:3000 rpm; D:140.0000 mm; Basic Dynamic Radial Load Rating C:72800 N; d:80.000 mm; Accessories:Two Shields; Basic Static Radial Load Rating Co:53000 N; |
| 162.45.2366.890.11.1503 Standard 5 Slewing Ring Bearings | Recommended tightening torque for grub screw:4 N·m; r1,2 min.:0.6 mm; Calculation factor f0:13; Fatigue load limit Pu:0.28 kN; d:19.05 mm; D:47 mm; B:31 mm; Hexagonal key size for grub screw N:3.175 mm; Thread grub screw G2:1/4-28 UNF; Limiting speed1):5000 r/min; C:14 mm; Basic static load rating C0:6.55 kN; d1 ≈:28.2 mm; Mass complete bearing:0.16 kg; B4:4.5 mm; s1:18.3 mm; Basic dynamic load rating C:10.8 kN; |
| 60.25.1155.500.11.1503 Standard 5 Slewing Ring Bearings | Accessories:One Seal; Basic Static Radial Load Rating Co:236000 N; B:68.30 mm; Oil Speed Rating n2:3400 rpm; d:80.000 mm; Grease Speed Rating n1:2400 rpm; Sealed Speed Rating n3:2400 rpm; Basic Dynamic Radial Load Rating C:201000 N; D:170.0000 mm; Fillet Radius ra:2.00 mm; |
| 92.20.1246.990.11.1503 Standard 5 Slewing Ring Bearings | N4:4 mm; Mass bearing unit:2.65 kg; B:51.6 mm; J6:187 mm; J:157 mm; J min.:149 mm; H1:57.2 mm; A:54 mm; A5:29.5 mm; H2:22 mm; N:26 mm; B4:9 mm; Recommended diameter for attachment bolts, inch G:0.625 in; Hexagonal key size for grub screw N:4.763 mm; H:114 mm; L:203 mm; Recommended diameter for attachment bolts, mm G:16 mm; Limiting speed:800 r/min; Fatigue load limit Pu:0.98 kN; J7:19 mm; |
| 61.25.1355.500.11.1503 Standard 5 Slewing Ring Bearings | Snap ring Seeger:SW 230; D:230 mm; Limiting speed:530 r/min; Snap ring in accordance with DIN 471:230x5; Fatigue load limit Pu:110 kN; r3,4 min.:0.6 mm; C1:71.2 mm; C:79 mm; r min.:1.8 mm; B:80 mm; das:190 mm; +:0.2 mm; Calculation factor kr:0.4; b1:7 mm; -:0.2 mm; ra max.:1.5 mm; Mass bearing:9.2 kg; da min.:177 mm; Basic dynamic load rating C:512 kN; Ca2:61 mm; |
| 280.30.1200.013 Type 110/1400. Standard 5 Slewing Ring Bearings | Basic static load rating C0:21.6 kN; B:19 mm; D1 ≈:72.4 mm; Mass bearing:0.37 kg; r1,2 min.:1.1 mm; ra max.:1 mm; d:45 mm; Calculation factor kr:0.025; Da max.:78 mm; d1 ≈:57.6 mm; Fatigue load limit Pu:0.915 kN; Basic dynamic load rating C:35.1 kN; Calculation factor f0:14.2; D:85 mm; Limiting speed:13000 r/min; Reference speed:22000 r/min; da min.:52 mm; |
| 61.25.1455.500.11.1503 Standard 5 Slewing Ring Bearings | Corrosion protection:Zinc-coated housing; l1:40 mm; D:168 mm; J:133.35 mm; Recommended tightening torque for disc screws:100 N·m; B:82 mm; Minimum disc diameter min.:300 mm; Shaft design:Shaft with metric fe; B1:67 mm; Recommended minimum temperature min.:-20 °C; s:3.9 mm; Sealing system:SKF Mudblock seal; GS:M20x1.5; Basic dynamic load rating C:52.7 kN; Basic static load rating C0:45 kN; |
| 192.20.1400.990.41.1502 Standard 5 Slewing Ring Bearings | Grease Speed Rating Open/Shielded n1:5000 rpm; Fillet Radius ra:1.00 mm; Basic Static Radial Load Rating Co:31500 N; B:18.00 mm; Sealed Speed Rating n3:3100 rpm; D:125.0000 mm; Oil Speed Rating Open/Shielded n2:6000 rpm; Basic Dynamic Radial Load Rating C:32500 N; d:90.000 mm; Accessories:Two Shields; |
| 161.28.1400.890.11.1503 Standard 5 Slewing Ring Bearings | A:68.263 mm; J min.:198.438 mm; H2:57.15 mm; Basic dynamic load rating C:158 kN; Limiting speed:3400 r/min; A1:95.25 mm; Attachment bolt diameter G:19.05 mm; H1:82.55 mm; L:265.113 mm; s:31.75 mm; d2:111.125 mm; H:165.894 mm; B:92.075 mm; Mass bearing unit:9.98 kg; da:69.85 mm; S:0.794 mm; J max.:223.838 mm; |
| 12.40.2622.401.41.1502 Standard 5 Slewing Ring Bearings | M1:5 mm; Spring washer in accordance with DIN 128:A 12; M2:38 mm; M:15 mm; B:28 mm; Mass locking clip:0.069 kg; Hexagonal head bolt:M 12x25; M3:14 mm; |
| 11.40.2795.000.11.1502 Standard 5 Slewing Ring Bearings | Preload class C GC:240 N; Calculation factor f2C:1.05; Preload class B GB:120 N; Calculation factor fHC:1.02; Static axial stiffness, preload class C:76 N/µm; Mass bearing:0.17 kg; Calculation factor f2A:1; Calculation factor f:1.06; Preload class A GA:60 N; B:15 mm; Basic static load rating C0:11 kN; d:40 mm; D:68 mm; D1:58.8 mm; Static axial stiffness, preload class A:42 N/µm; d2:49.2 mm; |
| 162.40.2128.890.11.1503 Standard 5 Slewing Ring Bearings | B:25.40 mm; Grease Speed Rating Max. n1:24000 rpm; Keyway e:21.4 mm; Oil Mist Speed Rating Max. n3:45000 rpm; Preload:0 lb; X-L-O Part Number:55-107; D:50.8000 mm; Fillet Radius ra:1.00 mm; Keyway f:1.6 mm; Oil Speed Rating Max. n2:27000 rpm; d:20.640 mm; |
| 12.40.2950.000.11.1502 Standard 5 Slewing Ring Bearings | Permissible sliding velocity v min.:0 m/s; Mass bushing:0.97 kg; Coefficient of friction µ max.:0.08; B:150 mm; D:140 mm; Effective load carrying cross section A:20720 mm²; Tolerance shaft:h8; Specific dynamic load factor K:140 N/mm²; Tolerance housing:H7; Coefficient of friction µ min.:0.03; d:155 mm; Specific static load factor K0:200 N/mm²; Permissible sliding velocity v max.:0.5 m/s; |