| 281.30.1375.013 Type 110/1500.1 Standard 5 Slewing Ring Bearings | Recommended tightening torque for grub screw:16.5 N·m; Recommended diameter for attachment bolts, inch G:0.5 in; B1:56.3 mm; J:143.5 mm; N:22.5 mm; H:107 mm; J min.:135 mm; d:45 mm; Mass bearing unit:2.3 kg; L:187 mm; H1:54 mm; Thread grub screw G2:M10x1; Housing:SY 509 M/VZ033; Hexagonal key size for grub screw N:5 mm; A:48 mm; H2:21 mm; A1:32 mm; J6:173 mm; A5:23 mm; Recommended diameter for attachment bolts, mm G:12 mm; |
| 161.28.1600.890.11.1503 Standard 5 Slewing Ring Bearings | ra max.:5 mm; das:595 mm; d1 ≈:610 mm; Basic dynamic load rating C:5230 kN; Mass bearing:290 kg; Da max.:757 mm; Calculation factor e:0.3; Fatigue load limit Pu:780 kN; D1 ≈:702 mm; Basic static load rating C0:10600 kN; s max.:16 mm; D:780 mm; Db max.:757 mm; B:185 mm; E:732.3 mm; Calculation factor Y:0.4; Calculation factor kr:0.3; r1,2 min.:6 mm; da min.:553 mm; Limiting speed:400 r/min; |
| 91.50.2266.990.41.1502 Standard 5 Slewing Ring Bearings | H:920 mm; H2:155 mm; P150°:3500 kN; Oil level, min.:108 mm; Appropriate attachment bolt, size G:48 mm; Cap bolt, size:M 42x320; J1:260 mm; Cap bolt, rec. tightening torque:850 N·m; P120°:4000 kN; J:1110 mm; J6:1210 mm; Q120°:5800 kN; Oil level, max.:131 mm; N:70 mm; Appropriate attachment bolt, rec. tightening torque:5450 N·m; P55°:11200 kN; Da:780 mm; Bearing (basic designation):230/530 K; |
| 62.40.1500.000.19.1504 Standard 5 Slewing Ring Bearings | ra max.:0.15 mm; r1,2 min.:0.15 mm; Basic static load rating C0:0.09 kN; Calculation factor kr:0.025; Da max.:7.3 mm; d:3 mm; Basic dynamic load rating C:0.319 kN; D:8 mm; Calculation factor f0:6.1; D2 ≈:7.25 mm; da max.:4.3 mm; Mass bearing:0.00082 kg; Limiting speed:43000 r/min; B:4 mm; Fatigue load limit Pu:0.004 kN; da min.:3.9 mm; d1 ≈:4.35 mm; |
| 91.25.1310.990.11.1503 Standard 5 Slewing Ring Bearings | Fillet Radius rb:0.60 mm; Grease Speed Rating n1:8000 rpm; D:62.0000 mm; Fillet Radius ra:1.00 mm; d:30.000 mm; Oil Speed Rating n2:10000 rpm; Basic Static Radial Load Rating Co:26000 N; Basic Dynamic Radial Load Rating C:30700 N; B:32.00 mm; |
| 161.40.2000.890.11.1503 Standard 5 Slewing Ring Bearings | S:5.556 mm; P60°:39.1 kN; Ventilation fitting:38174-12; L:269.875 mm; A2:115.888 mm; RG:1/8 NPT; P90°:23.6 kN; J max.:228.6 mm; H:147.637 mm; A1:69.85 mm; Cap bolt recommended tightening torque:149.1 N·m; Pa:5.96 kN; Mass pillow block:10.7 kg; End plug (suffix Y):EPR 4; Ca:50.8 mm; P120°:14.2 kN; Housing:SAF 610; Max. speed for contact seal:3400 r/min; Contact seal:2 x B9784-15; |
| 280.30.1275.013 Type 110/1400. Standard 5 Slewing Ring Bearings | Distance J:47.6 mm; Weight W:0.45 kg; Insert Bearing IB:Stainless Steel; Dimension F:12.7 mm; Pin Dia BS:3/8; Dimension C:52.4 mm; Basic Dynamic Radial Load Rating:15600 N; Basic Static Radial Load Rating Co:11200 N; Diameter G:10.3 mm; Dimension B:138.1 mm; Distance H:31.8 mm; Width A:27.0 mm; Dimension L:82.6 mm; Dimension N:9.9 mm; Shaft Diameter D:30 mm; Dimension S1:22.2 mm; |
| 91.30.1607.991.21.1502 Standard 5 Slewing Ring Bearings | H:247.65 mm; L:422.275 mm; Basic dynamic load rating C:408 kN; S:0.794 mm; Attachment bolt diameter G:19.05 mm; J min.:333.375 mm; A:117.475 mm; Mass bearing unit:32.3 kg; da:112.713 mm; J max.:368.3 mm; H1:120.65 mm; Limiting speed:1900 r/min; A1:136.525 mm; J1:63.5 mm; H2:69.85 mm; B:155.575 mm; s:77.787 mm; d2:155.575 mm; |
| 61.25.1155.575.11.1403 Standard 5 Slewing Ring Bearings | Da:74.6 mm; Db2:71 mm; J7:19 mm; B:34.1 mm; GN:1/4-28 SAE-LT; Hexagonal key size for grub screw N:3.175 mm; A3:3.2 mm; Housing material:Cast iron; s1:19.8 mm; N4:4 mm; A5:20.5 mm; N:11.5 mm; Limiting speed:7000 r/min; DN:6.5 mm; SWN:7 mm; Basic static load rating C0:7.8 kN; R1:21 mm; T:38.8 mm; Thread grub screw G2:1/4-28 UNF; Recommended diameter for attachment bolts, mm G:10 mm; |
| 60.25.1155.500.11.1503 Standard 5 Slewing Ring Bearings | Accessories:One Seal; Basic Static Radial Load Rating Co:236000 N; B:68.30 mm; Oil Speed Rating n2:3400 rpm; d:80.000 mm; Grease Speed Rating n1:2400 rpm; Sealed Speed Rating n3:2400 rpm; Basic Dynamic Radial Load Rating C:201000 N; D:170.0000 mm; Fillet Radius ra:2.00 mm; |
| 12.30.2330.000.11.1503 Standard 5 Slewing Ring Bearings | Basic Dynamic Radial Load Rating C:60500 N; Sealed Speed Rating n3:5000 rpm; D:90.0000 mm; Accessories:Shield & Seal & Snap; Grease Speed Rating n1:5000 rpm; Basic Static Radial Load Rating Co:43000 N; B:36.50 mm; Fillet Radius ra:1.50 mm; Oil Speed Rating n2:6700 rpm; d:40.000 mm; |
| 162.28.1400.890.11.1503 Standard 5 Slewing Ring Bearings | P55°:250 kN; Basic dynamic load rating C:86.5 kN; N4 max.:6 mm; N:20 mm; Mass bearing unit:3.8 kg; ba max.:43 mm; Calculation factor Y2:3.3; S:2.5 mm; Calculation factor Y1:2.2; H:111 mm; Bearing mean diameter dm:53.5 mm; N1:15 mm; ba min.:34 mm; P0°:150 kN; P120°:95 kN; Basic static load rating C0:85 kN; Pa:15 kN; J6:185 mm; J:170 mm; Tightening torque for grub screws:8 N·m; |
| 11.40.2795.001.41.1502 Standard 5 Slewing Ring Bearings | B:42.00 mm; Accessories:Two Seals & Snap-Rin; Sealed Speed Rating n3:1500 rpm; Basic Static Radial Load Rating Co:173000 N; Fillet Radius ra:2.00 mm; Oil Speed Rating Open/Shielded n2:2800 rpm; D:260.0000 mm; Basic Dynamic Radial Load Rating C:168000 N; d:170.000 mm; Grease Speed Rating Open/Shielded n1:2200 rpm; |
| 12.35.1960.401.41.1503 Standard 5 Slewing Ring Bearings | Cap bolt, SAE grade:5; J max.:333.375 mm; da:88.9 mm; P90°:71.2 kN; Housing:FSAF 520; L:387.35 mm; N1:22.225 mm; Cap bolt recommended tightening torque:203.4 N·m; End plug (suffix Y):EPR 12; J1:60.325 mm; h:42.069 mm; P180°:48.9 kN; PG:1/4 NPT; Initial grease fill:365.71 g; H1:114.3 mm; R2:30.163 mm; P120°:44.5 kN; H:217.488 mm; Stabilizing ring:2 x SR-1520; Da:180 mm; |
| 92.35.1802.991.41.1502 Standard 5 Slewing Ring Bearings | G:M 90x2; B1:73 mm; Hydraulic nut:HMV 18 E; d:90 mm; Mass adapter sleeve assembly:1.4 kg; d1:80.963 mm; B:19 mm; d3:120 mm; |
| 12.35.2500.000.11.1503 Standard 5 Slewing Ring Bearings | H1:250.825 mm; Cap bolt:4 x 1 1/2-6 UNC; Ca:147.803 mm; P60°:449 kN; A2:315.119 mm; h:87.313 mm; J1:139.7 mm; Stabilizing ring:SR-0-40; J max.:749.3 mm; R1:163.512 mm; Cap bolt, SAE grade:5; H:495.3 mm; N1:41.275 mm; R2:50.8 mm; P180°:185 kN; Mass pillow block:364 kg; PosiTrac Plus contact element:2 x B10724-161; PG:1/4 NPT; Da:419.999 mm; Pa:82.7 kN; |
| No. | Brand | G | J | E | b | A | F | T | U |
| 61.25.1155.575.11.1403 | Standard 5 | - | - | - | - | - | - | 38.8 mm | - |
| 11.40.2619.000.11.1502 | Standard 5 | M 160x3 | - | - | - | - | - | - | - |
| 162.36.2000.891.41.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| 12.40.2622.401.41.1502 | Standard 5 | - | - | - | - | - | - | - | - |
| 12.40.2199.300.11.1502 | Standard 5 | - | - | - | - | - | - | - | - |
| 61.50.2130.001.49.1504 | Standard 5 | - | - | 29 mm | - | - | - | - | - |
| 92.25.1310.991.21.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| 161.36.2000.891.41.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| 161.36.1900.890.11.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| 61.40.1800.013.19.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| 162.50.2500.891.41.1503 | Standard 5 | 169.139 mm | - | - | - | - | - | - | - |
| 92.40.2003.991.41.1502 | Standard 5 | - | - | - | - | - | - | - | - |
| 162.28.1400.891.21.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| 12.30.1630.001.41.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| 92.35.1802.991.41.1502 | Standard 5 | M 90x2 | - | - | - | - | - | - | - |
| 282.30.1300.013 Type 110/1500.2 | Standard 5 | - | - | - | - | - | - | - | - |
| 162.25.1320.890.11.1503 | Standard 5 | - | 170 mm | - | - | 60 mm | - | - | - |
| 161.25.1320.890.11.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| 162.28.1500.891.21.1503 | Standard 5 | M 130x2 | - | - | - | - | - | - | - |
| 162.45.2654.891.41.1503 | Standard 5 | - | - | - | - | - | - | - | - |
162.25.1320.890.11.1503 Standard 5 Slewing Ring Bearings Video
KD 700 Series Rothe Erde slewing ring bearing , excavator
162.25.1250.891.21.1503,162.25.1320.890.11.1503,162.25.1320.891.21.1503. 161.28.1400.890.11.1503,161.28.1400.891.21.1503,161.28.1500.890.11.1503
Buy 162.25.1320.890.11.1503 slewing rings without gear - EF
Buy 162.25.1320.890.11.1503 slewing rings without gear from EF SLEWING BEARING CO., LTD.，thyssenkrupp rothe erde slewing bearing Distributor online
162.25.1320.890.11.1503 slewing ring bearings with ... - JCB Bearing
Page 1. Luoyang JCB Bearing Technology Co., Ltd
Buy 162.25.1320.890.11.1503 Four-point contact ball slewing rings
Buy 162.25.1320.890.11.1503 Four-point contact ball slewing rings from Turbine Bearing Supplier，Thyssenkrupp Rothe Rrde Slewing Bearing Distributor
162.25.1320.890.11.1503 de Rothe erde Coronas de orientación
Page 1. Luoyang JCB Bearing Technology Co., Ltd
RD 700 Series Rothe Erde slewing ring bearing ...
162.25.1250.891.21.1503,162.25.1320.890.11.1503,162.25.1320.891.21.1503 161.28.1400.890.11.1503,161.28.1400.891.21.1503,161.28.1500.890.11.1503
162.25.1320.890.11.1503 162.25.1320.891.21.1503 ... - JCB Bearing
162.25.1320.890.11.1503 162.25.1320.891.21.1503 Drawing of Rothe Erde slewing bearing Luoyang JCB Bearing Technology Company
Rothe Erde Slewing Bearing Luoyang JCB Bearing Import
162.25.1250.890.11.1503 162.25.1250.891.21.1503 162.25.1320.890.11.1503 162.25.1320.891.21.1503 162.28.1400.890.11.1503 162.28.1400.891.21.1503
China Cross Roller Slewing Ring Bearing with External Gears
162.25.1320.890.11.1503 162.25.1320.891.21.1503, 240, 1432, 1140. 161.28.1400.890.11.1503 161.28.1400.891.21.1503, 332, 1593.6, 1266
162.25.1320.890.11.1503 Rothe Erde Slewing Ring Bearings | Lily
We supply 162.25.1320.890.11.1503 slewing ring to customer according to Rothe Erde standard and specification, the quality of our product is same as original